







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterHow Much Does a Walk-In Shower Installation Cost in Arlington?
Walk-in shower installation in Arlington runs $4,500 to $12,000 for most homes, with the typical project landing around $7,800. A simple curbless shower with stock tile and a standard 60-inch pan sits near $4,500, while a custom-tiled shower with a frameless glass enclosure, built-in bench and niche pushes toward the $12,000 ceiling. The two biggest swing factors are waterproofing method and tile selection, not the plumber’s hourly rate.
That range assumes a permitted bathroom project in a Mid-Cities or Fielder Park home built between the 1950s and 2000s. Older masonry walls and slab-on-grade plumbing in Arlington’s established neighborhoods can add $800 to $2,000 in prep work that a stock tile-and-liner install would skip entirely.
Key Takeaways
- Typical installed cost: $4,500 to $12,000, mid-range project near $7,800.
- Waterproofing method (sheet membrane vs. liquid-applied vs. foam board) drives 15 to 25 percent of the variance.
- Arlington’s expansive clay soil and older slab plumbing often add $800 to $2,000 to foundation-adjacent shower work.
- Tile itself is rarely more than 20 percent of the total; labor and prep are the rest.
- Written price before any work starts, flat scope, signed change orders. Always. Under Clause 1 of The Haven Standard, that price is on paper before a tool comes out.

Walk-In Shower Installation Cost Breakdown (2026)
The table below shows how a $4,500 to $12,000 shower actually splits up. Numbers are installed cost in the Arlington market, not material-only.
| Line Item | Low | High | Notes |
|---|---|---|---|
| Demo and haul-away of existing tub or shower | $400 | $900 | Includes disposal and drywall repair where tile meets wall |
| Rough plumbing (drain relocation, valve, showerhead) | $600 | $1,800 | Moving the drain more than 12 inches is the higher end |
| Waterproofing (membrane + pan + curb) | $500 | $1,400 | Schluter-KERDI, Laticrete, or Schluter-style sheet systems |
| Tile installation (walls + pan) | $1,200 | $3,200 | Porcelain at the low end, large-format or mosaic feature at the high |
| Tile material | $400 | $2,000 | Widest range on the page; budget porcelain vs. marble-look porcelain |
| Glass enclosure (framed or frameless) | $500 | $2,200 | Frameless 3/8-inch glass with laser-measured panels is the high end |
| Fixtures (showerhead, valve, drain, hardware) | $300 | $1,200 | Kohler and Delta at the higher end of the range |
| Bench, niche, or curbless conversion | $400 | $1,600 | Curbless requires recessing the subfloor; niche and bench add labor only |
| Permit and inspection | $150 | $450 | Arlington Development Services permit; varies by scope |
Add all nine rows and you land between $4,450 and $14,750. The realistic middle, for a standard 60-inch alcove conversion in an Arlington home, is $7,000 to $8,500. Curbless showers and full custom tile push toward the ceiling. If you’re pulling a tub at the same time, look at our bathroom remodeling service to bundle the demo and prep.
What drives cost up: tile size (large-format 24×48 porcelain costs more to set than 12×12), glass (frameless adds $800 to $1,500), and drain relocation. What drives it down: keeping the existing drain location, choosing a framed enclosure over frameless, and using a prefabricated pan with a sheet membrane instead of a full mud bed.
What Affects Walk-In Shower Installation Pricing in Arlington
Arlington isn’t a generic Texas market. Six factors push price around here more than anywhere else.
- Age of the home. Homes in Fielder Park, Hillcrest, and Interlochen built before 1985 often have cast-iron or galvanized drain lines that crack or corrode during demo. We budget $400 to $1,200 for drain replacement when we find it, and it shows up in roughly a third of pre-1985 showers we tear out.
- Expansive clay soil and slab movement. Arlington’s Blackland Prairie clay swells and shrinks with every wet season. That movement transfers to slab-on-grade plumbing and to tile set on subfloor that has shifted. We check for deflection and floor level before setting tile. Missing that check is why some suburban showers have hairline cracks within 18 months.
- Waterproofing method. A sheet-applied membrane (Schluter-KERDI or Laticrete Hydro Ban) runs $500 to $1,400 installed. Skipping it, or substituting a painted-on coating over drywall, is the most common cause of failed showers we’re asked to correct. It’s also a shortcut we won’t take, and the written scope will say so.
- Glass and fixture selection. A framed pivot door runs $500 to $900. A frameless 3/8-inch glass panel with laser-measured edges runs $1,400 to $2,200. Showerheads and valves from Kohler or Delta sit at the higher end of the fixture range, but the spec is what drives the price, not the brand name alone.
- Permit scope. A walk-in shower that replaces a tub requires a plumbing permit in Arlington. Any change to the drain location or a curbless conversion requires inspection before tile goes down. Permit fees run $150 to $450 depending on scope, and they’re always in the written price.
- Tile selection and layout. Porcelain starts around $4 per square foot; marble-look porcelain at $9 to $14 per square foot, and natural stone at $15 to $30. A herringbone pattern adds 20 to 30 percent to setting labor versus a straight lay.
The technicians who handle our shower work have up to 19 years of experience, and the photo record we leave with every job shows the shower pan before tile, the membrane buildup, and the finished waterproofing result. That’s not an upgrade; it’s what we deliver on every visit.

How to Save on Walk-In Shower Installation
There are five moves that keep real money in your pocket without skipping the parts that fail.
- Keep the drain where it is. Relocating a shower drain adds $400 to $1,200. If the existing drain works with the new layout, leave it.
- Choose porcelain over natural stone. A $2,000 tile bill can become $500 with the right porcelain. Large-format matte porcelain reads as stone and cleans easier.
- Go with a framed enclosure. A clean framed glass door in a matte black or brushed nickel finish saves $800 to $1,500 compared to a frameless custom glass install. It looks fine in a guest bath.
- Bundle the shower with other bathroom work. If the vanity, toilet, or floor needs attention too, doing it in one permit and one demo reduces total cost by $1,000 or more. See our Arlington service area page for how that pairs with other work.
- Ask for the free second opinion. Bring any written estimate to us and we’ll review it line by line at no charge. We’ve flagged missing waterproofing, undersized permits, and glass allowances priced too low to actually deliver. If the number you have is fair, we’ll say so.
Free estimates are standard here. If you want to talk numbers before you commit, call (844) 761-7521 – we answer with a live person any hour, and the estimate is written, itemized, and flat.
Is It Cheaper to Repair or Replace a Walk-In Shower in Arlington?
Replacing a failed shower typically costs $3,000 to $6,000 and repairing one with recurring leaks runs $1,500 to $3,500 per attempt. Once a shower has failed waterproofing twice, replacement is cheaper than a third patch. The signal to watch: loose tile, a soft spot at the curb, or efflorescence (white mineral staining) working through grout lines. All three mean water is getting under the tile, and it’s not coming back out through the grout.
If you’re facing that decision, the honest test is a quick feel-check on the shower pan and curb and a look at the drain flange. We won’t patch a shower with a failed pan, because the failure is underneath everything we’d be touching. Call (844) 761-7521 for a free second opinion on any repair quote you’re holding.
Can You Install a Walk-In Shower in One Day in Arlington?
A walk-in shower takes 5 to 10 working days, not one. Same-day installs exist but only for prefabricated acrylic surround kits on an existing pan, which sits near the $3,000 to $4,500 end of the range and doesn’t involve tile. A tiled walk-in shower needs demo, rough plumbing, membrane, tile set, cure time for thinset (24 hours minimum), grout, and glass measurement, which typically adds 7 to 10 days for fabrication.
The two-week stretch matters because skipping steps to hit a one-day target is how showers fail. We won’t compress the cure time, and the written scope you get before work begins lists the days that step consumes. Call (844) 761-7521 to schedule an in-home estimate; we’ll walk the timeline with you and photograph what we find.
What Brands Do You Use for Walk-In Shower Installation in Arlington?
Fixtures from Kohler and Delta, waterproofing from Schluter-KERDI or Laticrete, and glass from a local fabricator measured on-site after tile is set. Tile brands we source regularly include Daltile, Marazzi, and Crossville, all available through Texas distributors with 2 to 3-week lead times. On the enclosure side, Basco and Coastal Industries offer stock framed and semi-frameless options available in days rather than weeks.
Bathroom hardware (valves, drains, showerheads) sits in the written scope by brand and model number, not by category. That’s how the quote is honest: the customer can look up a Kohler valve or a Delta showerhead and know exactly what’s arriving. Our sourcing runs across fifty-plus vetted brands across the trades we handle, from cabinets to roofing, but the shower page names only what’s actually in the shower.
Do You Need a Permit for a Walk-In Shower in Arlington?
Yes, a plumbing permit is required whenever the shower changes drain location, replaces a tub, or moves the valve. The City of Arlington Development Services office issues these permits, and an inspection happens before tile closes the wall. Budget $150 to $450 for the permit, which we include in the written price. Skipping the permit creates a disclosure problem at resale and a voided waterproofing warranty – two costs that vastly exceed the $150 to $450 saved.
We pull the permit as part of the job. The signed permit and inspection record are part of the documentation you receive when the crew leaves, along with the photo record and the written warranty under our 365-Day Done Right Promise. Call (844) 761-7521 to confirm permit scope for your exact shower layout.
What Warranty Comes With a Walk-In Shower Installation?
Our written warranty covers the finished shower for 365 days under the Done Right Promise: if it isn’t done right, we make it right. That includes grout issues, membrane failures, glass hardware problems, and fixture defects within the period. The warranty is printed on the agreement, and the terms are published, not buried in an asterisk. Components from Kohler, Delta, and tile manufacturers carry their own manufacturer warranties on top.
We print the warranty on the page and hand it to the customer at the same time we hand them the invoice. If the shower leaks at month nine, we don’t ask whether it’s “normal wear.” We repair it. That policy plus the photo record we leave on every visit is why customers refer us to neighbors in Arlington and beyond.
FAQs – Walk-In Shower Installation Cost
How much does a walk-in shower cost in Arlington, TX?
A walk-in shower in Arlington costs $4,500 to $12,000 installed, with most projects landing around $7,800. The low end ($4,500) is a stock 60-inch pan with porcelain tile and a framed door. The high end ($12,000) is a curbless custom-tiled shower with frameless glass, a built-in bench, and a niche. Call (844) 761-7521 for a written estimate on your exact layout.
Is it cheaper to repair a shower or replace it in Arlington?
Replacement is usually cheaper once a shower has failed twice. Patch repairs run $1,500 to $3,500 each, and if the pan or waterproofing has failed, the patch doesn’t fix the cause. A full replacement at $3,000 to $8,500 for a shower-only scope (or $4,500 to $12,000 with tile and glass) is the lower total cost after two failed repairs. Call (844) 761-7521 for a free second opinion on any written repair quote.
Can I get a walk-in shower installed in one day?
No, a tiled walk-in shower takes 5 to 10 working days. A prefabricated acrylic surround kit can sometimes be done in a single day, but that sits at the $3,000 to $4,500 end and doesn’t involve tile or custom glass. Thinset needs 24 hours to cure before grout, and glass needs to be measured after tile is set, so a one-day tiled install isn’t physically possible. Call (844) 761-7521 to schedule an estimate and we’ll walk the timeline.
What’s the difference between a tub-to-shower conversion and a walk-in shower installation?
A tub-to-shower conversion runs $3,500 to $10,000 and swaps a tub for a shower in the existing alcove. A walk-in shower install runs $4,500 to $12,000 and includes the full waterproofing, tile, and glass scope from studs out. The conversion is a subset of the install; the price gap comes from custom tile, glass, and bench or niche work. See our tub-to-shower conversion service for the subset pricing and scope.
Do you offer a warranty on walk-in shower installation in Arlington?
Yes, 365 days under the Done Right Promise, and it’s printed on the agreement. Grout failure, membrane leaks, glass hardware defects, and fixture problems within the year are covered. Manufacturer warranties on Kohler, Delta, and tile carry beyond that. Call (844) 761-7521 and we’ll walk you through what the warranty covers in writing before the job starts.
Get a Written Price Before You Decide
A walk-in shower is a $4,500 to $12,000 decision, and you deserve to see the number in writing before anyone touches a drain. We write the scope, the price, the timeline, and the warranty on one document, and no change proceeds without a signed change order. Bring any competitor’s estimate and we’ll review it line by line at no charge as our free second opinion. Call (844) 761-7521 for a free estimate, and we’ll photograph what we find and leave you with the record.
Pricing reflects the Arlington market as of 2026. Rowan Construction Group Arlington offers free estimates – call (844) 761-7521.
What Our Customers Say
"They found an old septic line under the driveway run and stopped, documented it, and re-quoted before continuing."
- Xavier L."Talked us out of the larger scope we came in asking for, because it would not have added the value we thought."
- Emil R."Fence and retaining wall along a sloped boundary. They photographed the footing depth at each post, which mattered when the county inspector came."
- Iona F.












